FAG Z-528996.TR2 Tapered roller bearings

D:22.0000 mm; Basic Static Radial Load Rating Co:1370 N; Sealed Speed Rating n3:23000 rpm; Oil Speed Rating Open/Shielded n2:43000 rpm; Basic Dynamic Radial Load Rating C:3250 N; Accessories:Synthetic Rubber Sea; B:11.99 mm; Fillet Radius ra:0.30 mm; Grease Speed Rating Open/Shielded n1:36000 rpm; d

D:165 mm; Maximum dynamic radial loads Fr max.:355 kN; d1 ≈:90 mm; D1 ≈:110 mm; Basic dynamic load rating C:314 kN; Mass bearing:14.6 kg; K:5 mm; H max.:47.5 mm; d:70 mm; Fatigue load limit Pu:61 kN;

Lubricant:Regular relubricatio; Basic static load rating C0:7650 kN; Da min.:224.5 mm; dk:225 mm; r1 min.:1.1 mm; Material constant KM:330; Specific static load factor K0:500 N/mm²; da max.:199 mm; rb max.:1 mm; M:6 mm;

Permissible sliding velocity v min.:0 m/s; Specific static load factor K0:45 N/mm²; D:28 mm; D1:35 mm; d:20 mm; Coefficient of friction µ max.:0.15; α:105 °; B:16 mm; Tolerance shaft:e7; Coefficient of friction µ min.:0.08;

ra max.:1.5 mm; Calculation factor e:0.43; r3,4 min.:1.5 mm; Da min.:108 mm; Ca min.:4 mm; 2B:62 mm; b:7 mm; D:125 mm; Basic dynamic load rating C:334 kN; Limiting speed:5300 r/min;

d2 (max):64.6 mm; rs (min):1.5 mm; d2:45 mm; s:1.4 mm; F:59 mm; b:7 mm; D:100 mm; B:25 mm; Static (Coa):98 kN; E:mm;

h:46.038 mm; Cap bolt:2 x 3/4-10 UNC; P120°:33.8 kN; Ca:67.793 mm; Initial grease fill:365.71 g; A1:98.425 mm; H2:44.45 mm; Da:170 mm; Mass pillow block:29.8 kg; P180°:36.9 kN;

Fillet Radius ra:2.50 mm; Oil Speed Rating Open/Shielded n2:3400 rpm; Grease Speed Rating Open/Shielded n1:2800 rpm; Basic Dynamic Radial Load Rating C:157000 N; D:190.0000 mm; d:90.000 mm; Basic Static Radial Load Rating Co:160000 N; B:43.00 mm; Accessories:Two Shields;

da max.:57 mm; ra max.:1.5 mm; Mass bearing:0.58 kg; T:26 mm; r3,4 min.:1.5 mm; Limiting speed:7500 r/min; Db min.:82 mm; C:20 mm; Fatigue load limit Pu:13.4 kN; Basic dynamic load rating C:106 kN;

Specific static load factor K0:45 N/mm²; Permissible sliding velocity v max.:0.5 m/s; Tolerance shaft:e7; Coefficient of friction µ min.:0.08; B1:8 mm; α:124 °; Tolerance housing:H7; a:1.75 mm; D1:85 mm; B:35 mm;

d:100 mm; Grease:2 000 min-1; D1:102 mm; d1:135 mm; rs (min):1 mm; static Cor:268.000 kN; dynamic Cr:95.310 kN; D:135 mm; Pu:10.790 kN; H:25 mm;

Specific dynamic load factor K:40 N/mm²; Coefficient of friction µ min.:0.06; Mass bushing:0.00078 kg; Tolerance shaft:h9; D:12 mm; Permissible sliding velocity v min.:0 m/s; Coefficient of friction µ max.:0.15; B:15 mm; d:10 mm; Tolerance housing:H7;

d:660 mm; D1 ≈:806 mm; r3,4 min.:6 mm; Basic static load rating C0:11800 kN; da min.:686 mm; D:880 mm; s max.:6 mm; Da max.:854 mm; Mass bearing:390 kg; Fatigue load limit Pu:830 kN;

rb max.:1 mm; Fatigue load limit Pu:49 kN; b1:6 mm; Basic static load rating C0:430 kN; s max.:2 mm; r1,2 min.:1.1 mm; Reference speed:1900 r/min; Da max.:144 mm; ra max.:1 mm; Basic dynamic load rating C:220 kN;

Accessories:No Shield, no Seal,; Oil Speed Rating n2:3400 rpm; Sealed Speed Rating n3:2400 rpm; Basic Static Radial Load Rating Co:193000 N; Fillet Radius ra:2.00 mm; d:90.000 mm; Grease Speed Rating n1:2400 rpm; Basic Dynamic Radial Load Rating C:151000 N; B:52.40 mm; D:160.0000 mm;